|
| |
|
EGGER is a family
enterprise, independent for over 50 years, and employing today more than
220 persons at the works in Switzerland and a further 100 in the rest of
Europe.
We specialize in
pumping slurries, aerated liquids and liquids at high temperatures and
pressures, as well as in flow measurement and regulation.
EGGER Pumps are for specific
technical purposes. Please refer to the individual pump types for
their intended special application.
We do not offer pumps for clean
water/liquid. |
Please click on the pictures for more details
SERIES T - TURO Vortex impeller |
|
 |
Fully recessed design
Discharge: DN 32 - 200 mm – (1 ¼” – 8”)
Capacity: up to 120 l/s – (1’900 usgpm)
Head: up to 130 m – (430ft)
Max. Operating temperature: Standard up to 180°C, Special up to
280°C – (360 to 540°F)
Max. Working pressures: 10 bar up to 30 bar (145-440psi)
Centrifugal slurry pumps for Heterogeneous solids, long fibrous
material and aerated slurries liquids (<10%).
Low shear design 15% liquid contact with impeller.
Unique casing design for improved hydraulic efficiency.
Non-clogging.
Low power consumption. Horizontal, Vertical, Shaft driven,
Cantilever & Submersible.
|
|
SERIES D - Channel vane impeller |
|
 |
Channel vane design
Discharge: DN 150 - 500 mm – (6”-20”)
Capacity: up to 1500 l/s –(23’800 usgpm)
Head: up to 90 m – (300ft)
Max. Operating temperature: Standard up to 120°C, (250°F)
Max. Working pressures: 6 bar up to 12 bar (87-175psi)
Centrifugal slurry pumps for solids, fibrous material. Impeller is
centrally located in the casing thereby reducing radial loads on the
seals and bearings also contributing to reduced wear in the casing.
Large solids handling ability. Low power consumption. Horizontal,
Vertical, Shaft driven, Cantilever & Submersible.
|
|
SERIES EO/EOS - Semi open impeller
|
|
 |
Semi open impeller design
Discharge: DN 50 - 500 mm –(2”-20”)
Capacity: up to 1300 l/s – (20600 usgpm)
Head: up to 210 m – (690ft)
Max. Operating temperature: Standard up to 180°C, Special up to
380°C – (360-680°F)
Max. Working pressures:10 bar up to 100 bar (145-1’450psi)
Centrifugal slurry pumps for Homogeneous solids, long fibrous
material and slurries with entrained gasses, (<25%) For single, two
and three phase slurries. High efficiency, minimal power
consumption. Low NPSH requirement.
Horizontal, Vertical, Shaft driven, Cantilever & Submersible.
|
|
RPP/RPG
- Axial flow elbow propeller pump |
|
 |
Discharge: DN 250 - 1300 mm (10”-51”)
Capacity: up to 5000 l/s –(79’200 usgpm)
Head: up to 10m (special design 30m) 33ft – 98ft
Max. Operating temperature: Standard up to 180°C, Special up to
380°C – (360-680°F)
Max. Operating temperature Standard up to 180°C (special design
280°C) 360°F-530°F
Axial flow pumps for homogeneous suspensions, liquids with crystals
or long fibers, aerated liquids (<5%) High efficiency, Low friction
drag coefficient, special blade profile for long fibers. Horizontal
with various drive arrangement options.
|
|
BS - IRIS diaphragm control valve |
|
 |
Flanges: DN 25 – DN 400 mm (1”-16”)
Max. Service pressure: 2 – 6 bars (30-90psi)
Max. Service temperature: (120°C 250°F)
Regulation of liquids, powders and gasses.
Centrally symmetrically regulated flow, stable regulating
characteristics without Hysteresis, low pressure loss and energy
efficient. Patented flow measurement and regulation system available
on request.
|
Thanks to its modular design, you can select your pump
tailor-made with an hydraulic, a construction and shaft sealing as well as
suitable materials without compromising your requirements.
For any requirement that you can not find in the product
selection above, please just send us the details and we will find a good
solution for you.
Key Benefits
-
Professional Manufacturer with outstanding
engineering for special solutions
-
Proven Swiss Quality product.
-
Sales, After Sales Support and Service through ROTEQ in Singapore
|
